Maschinen Wicke GmbH - Sondermaschinen - Kommunaltechnik
Mäh-Saugkombination Same
WKB 6502
Unimog Mäh-Saugkombination
Trichterstreuer
Tremo Carrier Mäh-Saugkombination
Laubberger
Mäh-Saugkombination Holder
FSI 300 3H an Tremo Carrier
Mäh-Saugkombination Same Frutetto 3
Schneeschild mit Kastenstreuer
Mäh-Saugkombination Tremo Carrier Bodenentleerung
Frontkehrmaschine FKB 150 leicht
Mäh-Saugkombination Holder V130

Products: Mowing products from Maschinen Wicke GmbH in Ellingen, Bavaria

Front mounted rotary mower, hydraulic

  • Hydraulic drive powered by vehicle hydraulics
  • Working width approx 80 cm to max 4 m
  • Ejector: left, right, centre, or rear
  • Including deflector plate (on side ejector)
  • Tyres 11 x 7-4 or solid rubber 180-80
  • Cutter length 400-640 mm
  • Minimum requirements:
    • Hydraulic system min 33 litres oil, max 100 litres oil at 180 bar
    • Feed line, return line, and unpressurised oil leak port
    • Coupling triangle, front plate, etc.

Accessories

  • Lifting/tilting mechanism (1 x single-acting control device)
  • Bolt-on mulching device
  • Foam filled runners
FSI 150 HM passend an Tremo Carrier FSI 180 HM passend an Tremo Carrier FSML 125 HM passend an Holder X30
FSML 150 RA FSML 150 HM passend an Jungo Jet FSML 180 HM


Front mounted rotary mower, mechanical

  • Drive powered by front PTO
  • Working width approx 80 cm to max 4 m
  • Ejector: left, right, or rear
  • Including deflector plate (on side ejector)
  • Tyres 11 x 7-4 or solid rubber 180-80
  • Cutter length 400-640 mm
  • Minimum requirements:
    • Front PTO min 540 rpm to max 2000 rpm
    • Lower link hooks and upper link or
    • Coupling triangle

Accessories

  • Lifting/tilting mechanism (1 x single-acting control device)
  • Bolt-on mulching device
  • Foam filled runners
FSML 150 LA geklappt FSI 220 RA passend an Reform Metrac FSI 200 RA passend an Same
FSI 165 RA AM FSI 200 RA passend an Reform Metrac FSI 165 RA AM


High capacity mower

  • Hydraulic/mechanical drive
    • 1. Mechanical centre section powered by front PTO
    • 2. Hydraulic centre section powered by vehicle hydraulics
    • 3. Hydraulic centre section powered by (front or rear PTO) external hydraulic system
  • Working width 2 m to max 3.5 m
  • Rear ejector (mulching possible with low grass height)
  • Runners 11x7-4
  • Cutter length 400-640 mm
  • Minimum requirements:
    • 2 x circuit of 50 litres each oil at 180 bar
    • Feed line, return line, unpressurised oil leak port
    • 1 x single-acting control device for lifting/tilting mechanism
    • 2 x single-acting control device for side sections

Accessories

  • Foam filled runners
  • Mulching blades
FSI 240 3H 04 FSI 340 3H
06 FSI 300 3H FSI 300 RA passend an Unimog UX318